Futaba 10J Manuel d'utilisateur Page 175
- Page / 175
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
175
■ THR-REV
■ LANGUAGE
This function is not used. When you want to use full throttle with the throttle stick down
and slow with the throttle stick up, select REV. When the stick is up, trim is effective and
when the stick is down, trim is not effective.
*Throttle servo operation reversed by the linkage is usually performed by reverse in the
normal menu. When throttle servo operation is reversed with the THR-REV function, trim
becomes ineffective at slow.
The language displayed at proportional can be changed. The initial setting is English, but
can be selected from among 7 languages.
Return from the transmitter setting screen to the normal menu by turning on the power
without pressing a key.
④ Swing the selected stick fully
to the left and right (up and
down).
⑤ ■ appears next to "LEFT"
and "RGHT". Press the Jog
key.
⑥ When "COMPLETE" is
displayed, adjustment is
complete.
END
① Turn off the power and then
turn on the power while
pressing the + key and ‒ key
simultaneously.
② Select THR-REV → NOR
in the menu with the Jog
key.
③ Select NOR or REV by
pressing the + key or ‒ key.
Setting is ended by power
off.
THR-REV
＋ −
＋
−
① Turn off the power and then
turn on the power while
pressing the + key and ‒ key
simultaneously.
② Select
LANGUAGE → English in
the menu with the Jog
key.
③ Select NOR or REV by
pressing the + key or ‒ key.
Setting is ended by power
off.
LANGUAGE
＋ −
＋
−
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
2014, 02 (2)
- INSTRUCTION MANUAL 1
- Entire Contents © 2014 2
- 7$%/(2)&217(176 3
- Introduction 10
- BEFORE USE 12
- SYSTEM COMPATIBILITY 13
- Before use 14
- TRANSMITTER CONTROLS - HELI 16
- SWITCH ASSIGNMENT TABLE 18
- TO TURN ON THE 10J SYSTEM 18
- $LUFUDIW 19
- 0XOWLFRSWHU 19
- CHARGING THE BATTERIES 22
- A screw touches a case 23
- ADJUSTING DISPLAY CONTRAST 24
- CONNECTOR / PLUG 24
- WARNING & ERROR DISPLAYS 26
- RECEIVER NOMENCLATURE 28
- R3008SB CH MODE 29
- Coaxial cable 30
- R3008SB Receiver 30
- MOUNTING THE POWER 31
- SAFETY PRECAUTIONS 31
- MOUNTING THE SERVO 31
- RANGE CHECK THE RADIO 32
- S.BUS/S.BUS2 INSTALLATION 33
- S.BUS WIRING EXAMPLE 34
- 6%867$%/( 35
- S.BUS/S.BUS2 DEVICE SETTING 36
- TELEMETRY SYSTEM 37
- Common function 38
- Common function 39
- Model name ／ User name 43
- Fail safe 45
- Servo reverse 47
- Select timer mode 48
- Servo monitor ／ Servo test 49
- End point 50
- Trim reset ／ Trim step 51
- Sub trim 52
- Program mixing 1 ∼ 6 53
- AUX Channel 56
- Parameter function 58
- EXT-VOLT 70
- "VIB" types 72
- "VIB" type 75
- Altitude 80
- Sensor Slot 83
- Sensor connect 84
- Sensor connection 85
- S.BUS servo link 89
- Model transfer 92
- Trainer code 93
- "TRAINER" 94
- ■ Function activation 94
- ■ Mode setting 94
- ■ Student rate setting 94
- Airplane Function 95
- Airplane 96
- Aileron → Rudder mixing 98
- Gyro sensor 100
- Ailvator 102
- Throttle → Needle mixing 103
- Dual rate ／ EXPO 104
- Flaperon 106
- Air brake 108
- Flap → Elevator mixing 110
- Elevator → Flap mixing 111
- Flap trim 112
- Throttle cut 113
- Idle down 115
- Snap roll 116
- Throttle curve（Airplane） 117
- Pitch curve（Airplane） 118
- Throttle delay 119
- HELICOPTER Function 120
- Helicopter 121
- Condition select 122
- Swash AFR 123
- Swash mixing 124
- Swash ring 126
- Trim offset 127
- Gyro mixing 131
- CAUTIONS 134
- Pitch → Rudder mixing 138
- Throttle hold 140
- Governor mixing 141
- What is a governor ？ 142
- Hovering throttle 143
- Hovering pitch 144
- HI/LO-pitch trim 145
- Throttle mixing 146
- Throttle → Needlemixing（ 147
- Glider function 148
- ●Jog key 149
- Aileron differential 150
- Aileron → Rudder 151
- Motor switch 156
- Condition 157
- Rudder → Aileron 158
- Camber flap 159
- Camber mixing 160
- Butterfly mixing 161
- Camber → Elevator mixing 162
- Elevator → Camber mixing 163
- （ELE → Camber ） 164
- RANGE setting 164
- Roll is corrected by using 165
- Trim mix 167
- Multicopter Function 168
- Multicopter 169
- Calling the setting screen 173
- Position setting 173
- TX SETTING 174
- ■ THR-REV 175
- ■ LANGUAGE 175
- 2014, 02 (2) 175
Produits connexes et manuels pour Accessoires de communication Futaba 10J
(127 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.411 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels