Futaba R6014HS Manuel d'utilisateur télécharger pdf

Usage condition on "High Speed mode"

󾙏

CAUTION

󾙋

Outputs from 1ch to 6ch accept the

digital servos only or most type of

peripherals.

• If any analog servos connected to these output

as it will cause malfunction. Please check the

peripherals if there's any malfunction with whole

stick lever throw. If any malfunction occur please

change the operation mode to "Normal mode."

• Output of other channels shown below allow to

use any type of servos.

R6008HS - 7ch and 8ch

R6014HS - 7ch to 12ch, DG1, DG2

TM8

(on 8ch mode)

, TM10

(on 10ch mode)

, TM14

(on multi-ch mode)

R6008HS/R6014HS

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model

number R6008HS/R6014HS, complies with part15 of the FCC

Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

TEL (217)398-0007 or E-mail: [email protected] (Service)

R6008HS/R6014HS Speci-

cations

• Dual antenna diversity

• Power requirement: 4.8V or 6.0V battery

or regulated output from ESC, etc. (*1)

• Size: R6008HS: 0.98 x 1.86 x 0.56 in.

(24.9 x 47.3 x 14.3 mm)/R6014HS: 2.06 x

1.48 x 0.63 in. (52.3 x 37.5 x 16.0 mm)

• Weight: R6008HS: 0.48 oz. (13.5g)/

R6014HS: 0.72 oz. (20.8g)

(*1) Be sure that when using ESC's regulated

output the capacity of the ESC must meet

your usage condition.

Re-adjust the F/S position (only

for TM-8)

Press and hold the Link/Mode switch

between one(1) and two(2) seconds.

0 to 1 sec. 1 to 2 sec. More than 2 sec.

0 sec. 1 sec. 2 sec.

Press and Hold time

No function

With TM-8

(not included in this set)

To set the F/S

position(No re-link)

Re-link(ID set) and to

set the F/S position

No function

With TM-10, TM-14

(not included in this set)

Re-link(ID set)

FUTABA CORPORATION Phone: (043) 296-5118 Facsimile: (043) 296-5124

Makuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan

1M23N17413 ©FUTABA CORPORATION 2009, 01 (1)

LED

Link/Mode Switch

R6008HS

R6014HS

LED

Link/Mode

Switch

Operation Mode Select

The operation mode is on "Normal mode" from

factory shipping. When to change the mode,

please follow the steps shown below.

Turn off the receiver.

Press and hold the link/mode switch and

turn on the receiver. Keep the switch hold

more than one(1) second. The LED starts

ﬂashing with the current status.

Release the switch.

Turn off the receiver.

By doing this step, the mode can switch over

between two(2) modes.

0 to 1 sec. More than 1 sec.

0 sec. 1 sec.

Press and Hold time

Turn on the receiver.

No function

Showing the CURRENT

mode with blink.

Red Blink = Normal

Green/Red Blink =

High Speed

Solid as the mode changed.

Red Solid = Normal

Green/Red Solid = High

Speed

(Become Red after one (1)

second)

（

Function

）

To change the mode between

Normal and High Speed

（

LED

Status

）

Please check the operation mode by observing

the LED when turning on the receiver. If possible

there's no FASST transmitter turned on around you

in order to make rmer check.

When turn on the receiver, the LED will be;

• Red when on "Normal mode"

• Green and Red (makes Orange) when on "High

Speed mode". (After two(2) seconds, change to Red.)

If there are some FASST transmitter turned on

around the receiver, the LED may show the above

status for a brief moment then changed to the

status indication as shown in the "LED indication"

table.

LED Indication

Green Red Status

Solid Solid Initializing

Off Solid No signal reception

Solid Off Receiving signals

Blink Off Receiving signals but ID is unmatched

Link to the transmitter

Press and hold the Link/Mode switch more

than two(2) seconds.

󾙏

WARNING

󾙍

Do not perform the linking procedure

with motor's main wire is connected

or the engine is operating as it may result in

serious injury.

󾙋

While the linking is done, please

cycle receiver power and check if

the receiver to be linked is really under the

control by the transmitter to be linked.

Th ank y ou fo r pu rchas ing t he

R6 00 8HS

R6014HS

FASST receiver. These models have

two(2) operation mode as shown below.

Normal mode/High Speed mode

The "Normal mode" accepts any type of servos

or the peripherals as the frame rate of the output

is 14ms. The "High Speed mode" only accept

the digital servos for outputs from 1ch to 6ch,

including BLS series, and most peripheral

equipments such as the gyros or brushless ESCs.

The frame rate of the outputs is 7ms. The outputs

for other channels indicated below allow to use

any type of servos as the frame rate of these

outputs are still 14ms on the High Speed mode.

R6008HS - 7ch and 8ch

R6014HS - 7ch to 12ch, DG1, DG2

The

R6008HS

R6014HS

are compatible with

the FASST transmitters as shown below.

MPDX-1 application(R6014HS

only)

When to use the

MPDX-1

, please prepare the

exclusive short-plug shown below.

Short-plug

(sold separately)

Please insert the short-plug to

R6014HS

"DATA" port.

Short-plug

CH11 and CH12 are valid to use of MPDX-1.

Other channels can not use the MPDX-1.

• When not to use the MPDX-1, do not plug the

short-plug to the "DATA" port.

• Please note that when the short-plug is plugged

to the "DATA" port, both CH11 and CH12 become

acceptable for MPDX-1. CH11 or CH12 can not

separately set as the "MPDX-1-ready-output."

Résumé du contenu

Page 1

Usage condition on "High Speed mode"󾙏CAUTION󾙋 Outputs from 1ch to 6ch accept the digital servos only or most type of peripherals

Modèles reliés R6008HS

Commentaires sur ces manuels

Pas de commentaire

Futaba R6014HS Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires de communication Futaba R6014HS. Futaba R6014HS User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés R6008HS

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Futaba R6014HS