Futaba R2104GF Manuel d'utilisateur télécharger pdf

R2104GF

S-FHSS/FHSS-2.4GHz system

(Auto Detection),

4-channel receiver

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model number R2104GF, complies

with part15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: [email protected] (Support)

Thank you for purchasing the

R2104GF

receiver.

The

R2104GF

is designed for use with the Futaba

S-FHSS

FHSS

system transmitter. The

S-FHSS

system has two(2) operation mode as shown below.

•Normal mode/High Speed mode

The "Normal mode" accepts any type of servos

or the peripherals as the frame rate of the output

is 13.6ms. The "High Speed mode" only accepts

the digital servos, including BLS series, and most

peripheral equipments such as the brushless ESCs.

The frame rate of the outputs is 6.8ms.

Please pay special attention to the information

contained within this manual and transmitter's

manual in order to have a pleasant running/ying

experience.

The

R2104GF

is compatible with the

S-FHSS

FHSS

system transmitters as shown "Transmitter

and Receiver Compatibility".

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

1M23N17432 ©FUTABA CORPORATION 2010, 8 (1)

R2104GF Specications:

(

S-FHSS/FHSS

system, 4-channel receiver)

•Receivingon2.4GHzband

•System:

S-FHSS/FHSS

system(autodetection)

•Operationmode:Normal/Highspeed(autodetection)

•Powerrequirement:4.8Vor6V(sharedwithservo)

•Currentdrain:30mA(atnosignal)

•Size:1.54x1.02x0.39”(39x26x10mm)

•Weight:0.28oz.(8g)

󾙏

WARNING

󾙍

NEVER use drybatteries for

thepowersupplyoftheR2104GF

astheymaycausedifculties.

Link Procedure

Each transmitter has an individually assigned,

unique ID code. In order to start operation, the

receiver must be linked with the ID code of the

transmitter with which it is being paired. Once the

link is made, the ID code is stored in the receiver

and no further linking is necessary unless the

receiver is to be used with another transmitter.

Placethetransmitterandthereceiverclose

toeachotherwithinone(1)meter

Turnonthetransmitterandthereceiver.

 Push and hold the Link switch on the

receiver.

Whenthelinkiscomplete,theLEDonthe

receiverchangestosolidgreen.

*Please referto the table below for LED status

andreceivercondition.

Nosignalreception Red:On

Receivingsignals Green:On

Receivingsignals,butID

isunmatched.

Green:Blink

*If there are many

S-FHSS/FHSS

 systems turned

onaroundyourreceiver,itmightnotlinktoyour

transmitter. In this case, even if the receiver’s

LED stays solid green, unfor tunately the

receivermighthaveestablishedalinktooneof

the other transmitters. This is very dangerous

if you do not notice this situation.  In order to

avoid the problem, we strongly recommend

you to double-check whether your receiver is

controlled byyour transmitter by giving throttle

input,etc.andthencheckingservoresponse.

󾙏

WARNING

󾙋

After the linking is done, please

cycle receiver power and check if

the receiverto belinkedisreally underthe

controlbythetransmittertobelinked.

󾙍

Do notperformthe linking procedure

with motor'smain wire connectedor

withtheengineoperatingasitmayresultin

seriousinjury.

FHSS-2.4GHz/S-FHSS-2.4GHz System

Transmitter and Receiver Compatibility

Transmitter

FHSS

Receiver

S-FHSS/FHSS

Receiver

R603GF

R2004GF

R2104GF

T2PL-2.4G (FHSS) Okay Okay

F/Sfunction:Ch2

T3PL-2.4G (FHSS) Okay Okay

F/Sfunction:Ch2

T4YF-2.4G (FHSS) Okay Okay

T4PL-2.4G

S-FHSS

High Speed

— Okay

F/Sfunction:Allchannels

B-F/Sfunction:Ch2

*DigitalservoonlyatHighSpeed

mode

Normal

FHSS Okay Okay

F/Sfunction:Ch2

Link switch LED

Ch output (1 to 4)

Battery terminal (B)

Operating Precautions:

Oncethe

R2104GF

detectsthe

S-FHSS

normalmode,

S-FHSS

 high speed

modeor

FHSS

 mode, the detected

modeislockedaslongasthepower

is ON.When need to change the

mode,pleasecyclepower.

Note:Futaba

FHSS/S-FHSS

systemand

FASST

systemarenotcompatibleeachother.

Usage condition on "High Speed mode"

󾙏

CAUTION

󾙋

When using the high-speed mode, use a

Futaba digital servo (including brushless

servo).Analogservoscannotbeused.

•Theuseofanalogservosmaycauseservotrouble.

Link Procedure 1

Résumé du contenu

Page 1 - Link Procedure

R2104GFS-FHSS/FHSS-2.4GHz system(Auto Detection),4-channel receiverCompliance Information Statement (for U.S.A.)This device, trade name Futaba Corpora

Commentaires sur ces manuels

Pas de commentaire

Futaba R2104GF Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires de communication Futaba R2104GF. Futaba R2104GF User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Futaba R2104GF