Futaba 8FGAS, 8FGHS 2.4GHz Manuel d'utilisateur Page 27
- Page / 139
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
27
<Basic Operation>
S.BUS Servo Channel Setting (R6208SB)
S.BUS servo channel setting can be performed by using an S.BUS compatible receiver, an SBC-1
channel changer or CIU-2 USB serial interface. To set the channel by using your R6208SB, please adhere
to the following steps:
Channel setting
1. Connect the accessory short-plug to the
DATA port of the receiver.
Short-plug
(accessory)
* Connect the short-plug to the DATA port only when an
S.BUS servo channel is set. Normally do not connect the
plug.
2. Connect an S.BUS servo to the conventional
system output connector(1 to 8)
corresponding to the channel you want to
set.
Output
connector
Channel setting
Mode A Mode B
1 1 9
2 2 10
3 3 11
4 4 12
5 5 13
6 6 14
7 7 15
8 8 16
* Channel setting mode A (ch1 to 8 setting mode) or channel
setting mode B (ch9 to 16 setting mode) can be set.
3. Turn on the receiver.
* At once when turning on the receiver, the channel setting is
completed in mode A.
(To switch to mode B, press the Link/Mode
button until the red and green LED starts to
blink simultaneously. The channel setting is
completed in mode B.)
* The LED corresponding to the setting mode blinks.
Mode A: Red blinks 3 times
Mode B: Green blinks 3 times
4. Turn off the receiver.
- 8FG SUPER 1
- TABLE OF CONTENTS 2
- <Introduction> 4
- BEFORE USE 10
- Transmitter controls 13
- Receiver nomenclature 21
- Battery Charging 22
- Home screen 24
- User Menu 25
- <Basic Operation> 27
- Channel setting 27
- Easy Link (T8FGS/R6208SB) 28
- The present model 29
- Ailvator (Dual Elevator) 32
- Helicopter 34
- Fasten about 5-10cm 35
- Margin in the lead wire 35
- R6208SB Receiver 36
- MODEL BASIC SETTING PROCEDURE 37
- 12. Throttle mixing setting 42
- 13. Other special mixings 42
- System Menu functions table 43
- Mode and switch selection 45
- Operating mode selection 45
- USER NAME 48
- H/W SETTING 50
- Stick calibration method 51
- START SEL 52
- AUTO LOCK 55
- AUTO LOCK 55
- <SensorTouch™> 56
- FUNCTIONS OF LINKAGE MENU 57
- SERVO MONITOR 58
- MODEL SELECT 59
- Model deletion 60
- Model name change 60
- Model copy 60
- MODEL TYPE 61
- FREQUENCY 63
- FUNCTION 64
- SUB-TRIM 66
- FAIL SAFE 68
- END POINT 69
- IDLE DOWN 71
- SWASH RING 72
- PITCH ADJ 75
- T1-T4 SET 76
- Warning display: 77
- DATA RESET 78
- MODEL MENU (COMMON FUNCTIONS) 79
- CONDITION 80
- Condition delay setting 81
- DUAL RATE 82
- Dual rate setting procedure 83
- PROG. MIX 84
- FUEL MIX 86
- Model Menu functions list 88
- ( ) 89
- PIT CURVE 90
- THR CURVE 91
- THR DELAY 92
- AIL DIFF 93
- FLAP SET 94
- AIL to CMBFLP 95
- AIL to BRAKEFLP 96
- AIL to RUD 97
- RUD to AIL 98
- CAMBER MIX 100
- Setting method 101
- ●Activate the function 101
- ●Condition delay setting 101
- ●Rate adjustment 101
- ELE to CAMBER 102
- CMBFLP to ELE 103
- BUTTERFLY 104
- Fixed (0) Fixed (offset 105
- ●Reference point adjustment 105
- TRIM MIX 106
- AIRBRAKE 108
- ●Gyro type selection 111
- ●Sensitivity setting 111
- AILEVATOR 113
- ( ) 114
- RUD to ELE 117
- SNAP ROLL 118
- ●Master/single mode selection 119
- ●Direction switch selection 119
- MODEL MENU (HELICOPTER) 120
- PIT CURVE/PIT TRIM 121
- High Pitch/Low Pitch Trim 123
- THR CURVE/THROTTLE HOVER TRIM 124
- Throttle Hover trim 125
- Throttle limiter function 126
- THR HOLD 127
- SWASH MIX 128
- THROTTLE MIX 129
- GYRO mixing 131
- GOVERNOR mixing 133
- MODE 0％ 50％ 100％ 110％ 134
- TIMER ST1/ST2 135
- Switch Setting Method 137
- *[LOGIC] display blinks 139
- *The mode display blinks 139
Produits connexes et manuels pour Accessoires de communication Futaba 8FGAS, 8FGHS 2.4GHz
(93 pages)Electrolux EOU6330K Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Öfen Electrolux EOU6330K.
Wir stellen 1 PDF-Handbücher Electrolux EOU6330K zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels