Futaba 8FGAS, 8FGHS 2.4GHz Manuel d'utilisateur Page 30
- Page / 139
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
30
<Receiver and Servo Installation>
RECEIVER AND SERVO INSTALLATION
Receiver switch
Receiver battery
Charging port
Servos
R6208SB (output connector section)
•B: Power supply
•CH1~8: Output connectors 1~8
•S.BUS: Output for S.BUS system
•DATA port: (factory use only)
CH1~8,
S.BUS,
B
Receiver and servos connection diagram
Always connect the necessary number of servos.
The receiver channel assignment depends on the
model type. See the Servo connection by model
type tables.
Receiver and servos connection
Connect the receiver and servos in accordance with the connection diagram shown below. Always read
[Precautions when mounting the receiver and servos] or [Before using]. When mounting the receiver and
servos to the fuselage, connect the necessary points in accordance with the model's instruction manual.
• S.BUS system
Different from conventional radio control systems the S.BUS system uses data communication to
transmit control signals from a receiver to a servo, gyro, or other S.BUS compatible device. This data
includes commands such as “move the channel 3 servo to 15 degrees, move the channel 5 servo to
30 degrees” to multiple devices. The S.BUS devices execute only those commands for their own set
channel. For this reason, it can be used by connecting multiple servos to the same signal line.
[Connection by S.BUS system]
S.BUS hub S.BUS hub
S.BUS output
S.BUS
Ch output/
Battery terminal
R6208SB
Battery
S.BUS servo
Conventional
servo
2ch 4ch
3ch 5ch
6ch
* Can also be used together with conventional servos.
* When using servos with a remote battery pack, use S.BUS Hub with Cable (2-way/remote battery pack use). Please refer
to the instruction manual of S.BUS Hub with Cable (2-way/remote battery pack use) for the connection method.
- 8FG SUPER 1
- TABLE OF CONTENTS 2
- <Introduction> 4
- BEFORE USE 10
- Transmitter controls 13
- Receiver nomenclature 21
- Battery Charging 22
- Home screen 24
- User Menu 25
- <Basic Operation> 27
- Channel setting 27
- Easy Link (T8FGS/R6208SB) 28
- The present model 29
- Ailvator (Dual Elevator) 32
- Helicopter 34
- Fasten about 5-10cm 35
- Margin in the lead wire 35
- R6208SB Receiver 36
- MODEL BASIC SETTING PROCEDURE 37
- 12. Throttle mixing setting 42
- 13. Other special mixings 42
- System Menu functions table 43
- Mode and switch selection 45
- Operating mode selection 45
- USER NAME 48
- H/W SETTING 50
- Stick calibration method 51
- START SEL 52
- AUTO LOCK 55
- AUTO LOCK 55
- <SensorTouch™> 56
- FUNCTIONS OF LINKAGE MENU 57
- SERVO MONITOR 58
- MODEL SELECT 59
- Model deletion 60
- Model name change 60
- Model copy 60
- MODEL TYPE 61
- FREQUENCY 63
- FUNCTION 64
- SUB-TRIM 66
- FAIL SAFE 68
- END POINT 69
- IDLE DOWN 71
- SWASH RING 72
- PITCH ADJ 75
- T1-T4 SET 76
- Warning display: 77
- DATA RESET 78
- MODEL MENU (COMMON FUNCTIONS) 79
- CONDITION 80
- Condition delay setting 81
- DUAL RATE 82
- Dual rate setting procedure 83
- PROG. MIX 84
- FUEL MIX 86
- Model Menu functions list 88
- ( ) 89
- PIT CURVE 90
- THR CURVE 91
- THR DELAY 92
- AIL DIFF 93
- FLAP SET 94
- AIL to CMBFLP 95
- AIL to BRAKEFLP 96
- AIL to RUD 97
- RUD to AIL 98
- CAMBER MIX 100
- Setting method 101
- ●Activate the function 101
- ●Condition delay setting 101
- ●Rate adjustment 101
- ELE to CAMBER 102
- CMBFLP to ELE 103
- BUTTERFLY 104
- Fixed (0) Fixed (offset 105
- ●Reference point adjustment 105
- TRIM MIX 106
- AIRBRAKE 108
- ●Gyro type selection 111
- ●Sensitivity setting 111
- AILEVATOR 113
- ( ) 114
- RUD to ELE 117
- SNAP ROLL 118
- ●Master/single mode selection 119
- ●Direction switch selection 119
- MODEL MENU (HELICOPTER) 120
- PIT CURVE/PIT TRIM 121
- High Pitch/Low Pitch Trim 123
- THR CURVE/THROTTLE HOVER TRIM 124
- Throttle Hover trim 125
- Throttle limiter function 126
- THR HOLD 127
- SWASH MIX 128
- THROTTLE MIX 129
- GYRO mixing 131
- GOVERNOR mixing 133
- MODE 0％ 50％ 100％ 110％ 134
- TIMER ST1/ST2 135
- Switch Setting Method 137
- *[LOGIC] display blinks 139
- *The mode display blinks 139
Produits connexes et manuels pour Accessoires de communication Futaba 8FGAS, 8FGHS 2.4GHz
(93 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels