Futaba 8FGAS, 8FGHS 2.4GHz Manuel d'utilisateur Page 29
- Page / 139
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
29
<Basic Operation>
Range Testing Your R/C System
It is extremely important to range check your models prior to each ying session. This enables you to
ensure that everything is functioning as it should and to obtain maximum enjoyment from your time ying.
The T8FGS transmitter incorporates a system that reduces its power output and allows you to perform such
a range check.
Range check mode
We have installed a special "Range check
mode" for doing a ground range check. To access
the "Range check mode" touch and hold the RTN
button while turning on the transmitter. Doing so
will bring up POWER MODE menu.
To activate the "Range check mode" touch the
RTN button and the range check mode screen will
appear.
During this mode, the RF power output is
reduced so the range test can be performed. In
addition, when this mode is activated the right
LED on the front of the transmitter starts blinking
and the transmitter gives users a warning with a
beeping sound every 3 seconds.
The "Range check mode" continues for 90
seconds and after that the power will return
to the normal level. To exit the "Range check
mode" before the 90 seconds, select the "RANGE
CHECK" at the top of the screen and touch the
RTN button again. This mode is available one
time only so if you need to re-use this function the
transmitter power must be cycled. NEVER start
ying when the "Range check mode" is active.
Should you require additional time to perform
a range check, highlight Restart before your time
expires and press the RTN button one time.
Range check procedure
1. With the "Range check mode" on, walk
away from the model while simultaneously
operating the controls. Have an assistant
stand by the model to confirm that all
controls are completely and correctly
operational. You should be able to walk
approximately 30-50 paces from the model
without losing control.
2. If everything operates correctly, return to
the model. Set the transmitter in a safe, yet
accessible, location so it will be within reach
after starting the engine or motor. Be certain
the throttle stick is in the low throttle position,
then start the engine or motor. Perform
another range check with your assistant
holding the aircraft with the engine running
at various speeds. If the servos jitter or move
inadvertently, there may be a problem. We
would strongly suggest you do not y until the
source of the difculty has been determined.
Look for loose servo connections or binding
pushrods. Also, be certain that the battery
has been fully charged.
The present model
- 8FG SUPER 1
- TABLE OF CONTENTS 2
- <Introduction> 4
- BEFORE USE 10
- Transmitter controls 13
- Receiver nomenclature 21
- Battery Charging 22
- Home screen 24
- User Menu 25
- <Basic Operation> 27
- Channel setting 27
- Easy Link (T8FGS/R6208SB) 28
- The present model 29
- Ailvator (Dual Elevator) 32
- Helicopter 34
- Fasten about 5-10cm 35
- Margin in the lead wire 35
- R6208SB Receiver 36
- MODEL BASIC SETTING PROCEDURE 37
- 12. Throttle mixing setting 42
- 13. Other special mixings 42
- System Menu functions table 43
- Mode and switch selection 45
- Operating mode selection 45
- USER NAME 48
- H/W SETTING 50
- Stick calibration method 51
- START SEL 52
- AUTO LOCK 55
- AUTO LOCK 55
- <SensorTouch™> 56
- FUNCTIONS OF LINKAGE MENU 57
- SERVO MONITOR 58
- MODEL SELECT 59
- Model deletion 60
- Model name change 60
- Model copy 60
- MODEL TYPE 61
- FREQUENCY 63
- FUNCTION 64
- SUB-TRIM 66
- FAIL SAFE 68
- END POINT 69
- IDLE DOWN 71
- SWASH RING 72
- PITCH ADJ 75
- T1-T4 SET 76
- Warning display: 77
- DATA RESET 78
- MODEL MENU (COMMON FUNCTIONS) 79
- CONDITION 80
- Condition delay setting 81
- DUAL RATE 82
- Dual rate setting procedure 83
- PROG. MIX 84
- FUEL MIX 86
- Model Menu functions list 88
- ( ) 89
- PIT CURVE 90
- THR CURVE 91
- THR DELAY 92
- AIL DIFF 93
- FLAP SET 94
- AIL to CMBFLP 95
- AIL to BRAKEFLP 96
- AIL to RUD 97
- RUD to AIL 98
- CAMBER MIX 100
- Setting method 101
- ●Activate the function 101
- ●Condition delay setting 101
- ●Rate adjustment 101
- ELE to CAMBER 102
- CMBFLP to ELE 103
- BUTTERFLY 104
- Fixed (0) Fixed (offset 105
- ●Reference point adjustment 105
- TRIM MIX 106
- AIRBRAKE 108
- ●Gyro type selection 111
- ●Sensitivity setting 111
- AILEVATOR 113
- ( ) 114
- RUD to ELE 117
- SNAP ROLL 118
- ●Master/single mode selection 119
- ●Direction switch selection 119
- MODEL MENU (HELICOPTER) 120
- PIT CURVE/PIT TRIM 121
- High Pitch/Low Pitch Trim 123
- THR CURVE/THROTTLE HOVER TRIM 124
- Throttle Hover trim 125
- Throttle limiter function 126
- THR HOLD 127
- SWASH MIX 128
- THROTTLE MIX 129
- GYRO mixing 131
- GOVERNOR mixing 133
- MODE 0％ 50％ 100％ 110％ 134
- TIMER ST1/ST2 135
- Switch Setting Method 137
- *[LOGIC] display blinks 139
- *The mode display blinks 139
Produits connexes et manuels pour Accessoires de communication Futaba 8FGAS, 8FGHS 2.4GHz
(93 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.267 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels