Futaba 8FGAS, 8FGHS 2.4GHz Manuel d'utilisateur Page 65
- Page / 139
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
65
<Functions of Linkage Menu>
Camber, Motor or Butterfly control group/
single setting is performed at the function
setup screen.
"G": Group (common to all conditions)
"S": Single (set for each condition)
Trim setting
Move the cursor to the "TRIM" item of the
channel you want to change and touch the
RTN button.
*The trim setup screen is displayed.
The following items can be set at the trim
setup screen:
Trim selection
Move the cursor to the trim, lever, etc. you
want to set and touch the RTN button.
*The setting can be changed.
Trim rate setting
Move the cursor to the [RATE] item and
touch the RTN button to switch to the data
input mode.
Set the trim rate by scrolling the touch sensor.
Initial value: +30%
Adjustment range : -150~+150%
(When the RTN button is touched for one second, the trim
rate is reset to the initial value.)
Touch the RTN button to end adjustment and
return to the cursor mode.
Trim mode selection
Move the cursor to the [MODE] item and
touch the RTN button to switch to the data
input mode.
Select the trim mode by scrolling the touch
sensor. A confirmation message appears.
Touch the RTN button to change the mode.
(To terminate input and return to the original
state, touch the S1 button.)
[NORM]: Normal mode. Normal trim (parallel
shift trim) operation.
[ATL]: ATL operation mode. Maximum
change near idle or low-stick position,
normally used with throttle trim. It is also
possible to reverse the travel.
*[NORMAL]/[REVERS] selection is possible at the "ATL"
item.
Throttle trim (helicopter only)
* The throttle trim at conditions other than normal condition
can be inhibited.
When other than normal condition is
selected, move the cursor to throttle trim on
the function setup screen and touch the RTN
button for 1 second.
*When "X" is displayed, THR trim is inhibited at conditions
other than normal condition.
Channel replacement
Move the cursor to the channel # you want
to replace and touch the RTN button to
switch to the data input mode.
Select the destination channel # by scrolling
the touch sensor. A confirmation message
appears. Touch the RTN button to replace
the channel. (To terminate input and return
to the original state, touch the S1 button.)
- 8FG SUPER 1
- TABLE OF CONTENTS 2
- <Introduction> 4
- BEFORE USE 10
- Transmitter controls 13
- Receiver nomenclature 21
- Battery Charging 22
- Home screen 24
- User Menu 25
- <Basic Operation> 27
- Channel setting 27
- Easy Link (T8FGS/R6208SB) 28
- The present model 29
- Ailvator (Dual Elevator) 32
- Helicopter 34
- Fasten about 5-10cm 35
- Margin in the lead wire 35
- R6208SB Receiver 36
- MODEL BASIC SETTING PROCEDURE 37
- 12. Throttle mixing setting 42
- 13. Other special mixings 42
- System Menu functions table 43
- Mode and switch selection 45
- Operating mode selection 45
- USER NAME 48
- H/W SETTING 50
- Stick calibration method 51
- START SEL 52
- AUTO LOCK 55
- AUTO LOCK 55
- <SensorTouch™> 56
- FUNCTIONS OF LINKAGE MENU 57
- SERVO MONITOR 58
- MODEL SELECT 59
- Model deletion 60
- Model name change 60
- Model copy 60
- MODEL TYPE 61
- FREQUENCY 63
- FUNCTION 64
- SUB-TRIM 66
- FAIL SAFE 68
- END POINT 69
- IDLE DOWN 71
- SWASH RING 72
- PITCH ADJ 75
- T1-T4 SET 76
- Warning display: 77
- DATA RESET 78
- MODEL MENU (COMMON FUNCTIONS) 79
- CONDITION 80
- Condition delay setting 81
- DUAL RATE 82
- Dual rate setting procedure 83
- PROG. MIX 84
- FUEL MIX 86
- Model Menu functions list 88
- ( ) 89
- PIT CURVE 90
- THR CURVE 91
- THR DELAY 92
- AIL DIFF 93
- FLAP SET 94
- AIL to CMBFLP 95
- AIL to BRAKEFLP 96
- AIL to RUD 97
- RUD to AIL 98
- CAMBER MIX 100
- Setting method 101
- ●Activate the function 101
- ●Condition delay setting 101
- ●Rate adjustment 101
- ELE to CAMBER 102
- CMBFLP to ELE 103
- BUTTERFLY 104
- Fixed (0) Fixed (offset 105
- ●Reference point adjustment 105
- TRIM MIX 106
- AIRBRAKE 108
- ●Gyro type selection 111
- ●Sensitivity setting 111
- AILEVATOR 113
- ( ) 114
- RUD to ELE 117
- SNAP ROLL 118
- ●Master/single mode selection 119
- ●Direction switch selection 119
- MODEL MENU (HELICOPTER) 120
- PIT CURVE/PIT TRIM 121
- High Pitch/Low Pitch Trim 123
- THR CURVE/THROTTLE HOVER TRIM 124
- Throttle Hover trim 125
- Throttle limiter function 126
- THR HOLD 127
- SWASH MIX 128
- THROTTLE MIX 129
- GYRO mixing 131
- GOVERNOR mixing 133
- MODE 0％ 50％ 100％ 110％ 134
- TIMER ST1/ST2 135
- Switch Setting Method 137
- *[LOGIC] display blinks 139
- *The mode display blinks 139
Produits connexes et manuels pour Accessoires de communication Futaba 8FGAS, 8FGHS 2.4GHz
(93 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.357 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels