Futaba 8FGAS, 8FGHS 2.4GHz Manuel d'utilisateur Page 63
- Page / 139
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
63
<Functions of Linkage Menu>
● Select the function name
and return to the Linkage
menu by touching the
RTN button.
<SensorTouch™>
FASST mode selection
The receiver type will determine whether you
utilize MULTI(MLT2/MULT) or 7CH setting in
"FASST".
MLT2/MULT: FASST-2.4GHz system Multi-ch mode
7CH: FASST-2.4GHz system 7ch mode
*Select the MLT2 or MULT setting for all Futaba FASST-
2.4G Multi-ch mode receivers, regardless of number of
channels (e.g., R6208SB/R6108SB/6008HS/R6014HS/
R608FS/R6014FS).
7CH setting for all Futaba FASST-2.4G 7ch mode receivers,
regardless of number of channels (e.g., R6004FF/R616FFM/
R607FS/R617FS).
For the most up-to-date list of receivers and their
respective compatibility, please refer to our web site at:
http://2.4gigahertz.com/receivers/index.html
FREQUENCY
FASST mode selection and area mode selection
FASST mode selection
1. Move the cursor to the "FASST" item and
touch the RTN button to switch to the data
input mode.
Select the mode by scrolling the touch
sensor. A confirmation message appears.
Touch the RTN button to change the mode.
(To terminate input and return to the original
state, touch the S1 button.)
*Transmission stops and then starts in the mode selected.
*When MLT2 mode is selected, the 12 linear CH output
mode is activated. In the MLT2 mode, 1-12CH setting is
possible on the function/sub-trim/servo reverse/fail safe/end
point/trainer screens. Virtual channels cannot be used in the
MLT2 mode.
*When MULT mode is selected, the 8 linear CH output and
the 4 virtual CH mode is activated.
Area mode selection (Frequency range)
The T8FGS transmitter has been designed
to function in many countries. If you will be
utilizing this transmitter in a country other than
France, please make sure that [AREA] is set to
"GENERAL". If, however, this transmitter will be
utilized in France, it must be set to "FRANCE" in
order to comply with French regulations.
Area mode selection
1. Move the cursor to the "AREA" selection and
touch the RTN button to switch to the data
input mode.
Select the Area by scrolling the touch sensor.
A confirmation message appears. Touch
the RTN button to change the mode. (To
terminate input and return to the original
state, touch the S1 button.)
*Transmission stops and then starts in the mode selected.
● Select [FREQUENCY] in the Linkage menu and
access the setup screen shown below by
touching the RTN button.
Scrolling
● Moving cursor
● Selecting mode
- 8FG SUPER 1
- TABLE OF CONTENTS 2
- <Introduction> 4
- BEFORE USE 10
- Transmitter controls 13
- Receiver nomenclature 21
- Battery Charging 22
- Home screen 24
- User Menu 25
- <Basic Operation> 27
- Channel setting 27
- Easy Link (T8FGS/R6208SB) 28
- The present model 29
- Ailvator (Dual Elevator) 32
- Helicopter 34
- Fasten about 5-10cm 35
- Margin in the lead wire 35
- R6208SB Receiver 36
- MODEL BASIC SETTING PROCEDURE 37
- 12. Throttle mixing setting 42
- 13. Other special mixings 42
- System Menu functions table 43
- Mode and switch selection 45
- Operating mode selection 45
- USER NAME 48
- H/W SETTING 50
- Stick calibration method 51
- START SEL 52
- AUTO LOCK 55
- AUTO LOCK 55
- <SensorTouch™> 56
- FUNCTIONS OF LINKAGE MENU 57
- SERVO MONITOR 58
- MODEL SELECT 59
- Model deletion 60
- Model name change 60
- Model copy 60
- MODEL TYPE 61
- FREQUENCY 63
- FUNCTION 64
- SUB-TRIM 66
- FAIL SAFE 68
- END POINT 69
- IDLE DOWN 71
- SWASH RING 72
- PITCH ADJ 75
- T1-T4 SET 76
- Warning display: 77
- DATA RESET 78
- MODEL MENU (COMMON FUNCTIONS) 79
- CONDITION 80
- Condition delay setting 81
- DUAL RATE 82
- Dual rate setting procedure 83
- PROG. MIX 84
- FUEL MIX 86
- Model Menu functions list 88
- ( ) 89
- PIT CURVE 90
- THR CURVE 91
- THR DELAY 92
- AIL DIFF 93
- FLAP SET 94
- AIL to CMBFLP 95
- AIL to BRAKEFLP 96
- AIL to RUD 97
- RUD to AIL 98
- CAMBER MIX 100
- Setting method 101
- ●Activate the function 101
- ●Condition delay setting 101
- ●Rate adjustment 101
- ELE to CAMBER 102
- CMBFLP to ELE 103
- BUTTERFLY 104
- Fixed (0) Fixed (offset 105
- ●Reference point adjustment 105
- TRIM MIX 106
- AIRBRAKE 108
- ●Gyro type selection 111
- ●Sensitivity setting 111
- AILEVATOR 113
- ( ) 114
- RUD to ELE 117
- SNAP ROLL 118
- ●Master/single mode selection 119
- ●Direction switch selection 119
- MODEL MENU (HELICOPTER) 120
- PIT CURVE/PIT TRIM 121
- High Pitch/Low Pitch Trim 123
- THR CURVE/THROTTLE HOVER TRIM 124
- Throttle Hover trim 125
- Throttle limiter function 126
- THR HOLD 127
- SWASH MIX 128
- THROTTLE MIX 129
- GYRO mixing 131
- GOVERNOR mixing 133
- MODE 0％ 50％ 100％ 110％ 134
- TIMER ST1/ST2 135
- Switch Setting Method 137
- *[LOGIC] display blinks 139
- *The mode display blinks 139
Produits connexes et manuels pour Accessoires de communication Futaba 8FGAS, 8FGHS 2.4GHz
(93 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels