Futaba 10C 2.4GHz Manuel d'utilisateur télécharger pdf (Page 20)

• The receiver contains precision electronic parts. It is the most delicate radio component on-board the model and should

EHSURWHFWHGIURPYLEUDWLRQVKRFNDQGWHPSHUDWXUHH[WUHPHV7RSURWHFWWKHUHFHLYHUZUDSLWLQ5&IRDPUXEEHURURWKHU

vibration-absorbing material. If appropriate, waterproof the receiver by placing it in a plastic bag and closing the open

end with a rubber band before wrapping it in foam. If moisture enters the receiver, intermittent operation or a failure may

result. Wrapping the receiver in a plastic bag also protects it from fuel and exhaust residue which, in some models, can

work its way into the fuselage.

Product Advisory — R6014FS Receiver

Whereas many previous receivers offered a signal output of 3.0 Volts, the latest generation of ICs has been

designed to operate at lower voltages in order to increase their operational speeds. The R6014FS receiver

utilizes such an IC and, as such, the nominal signal output voltage of the R6014FS receiver is 2.7 Volts.

While this variance in the output voltage will not affect most equipment in use today, it has been brought to

our attention that some manufacturers’ products are not capable of operation with the lower signal voltage.

That is, they will not operate below 3.0 Volts. Some examples of what we have had reported thus far include

sequencers, cut-off valves, older servo designs and some recent non-Futaba digital servos.

6RPHEDWWHU\EDFNXSGHYLFHVPLJKWKDYHGLI¿FXOWLHVZLWKWKHORZHURSHUDWLRQDOYROWDJHVDVZHOODOWKRXJK

they might not appear to initially. One such device functions perfectly on the ground and during a range

check, yet when the operational temperature reaches 50°C (122°F), the device actually requires 2.8 Volts in

order to function properly. As such, the servos will cease to operate properly.

Many manufacturers are updating or refining their products to ensure compatibility with the lower

operational voltages. If you have any questions about the operation of such peripheral items we strongly

suggest that you contact the manufacturer directly.

If you have already purchased items which can not operate below 3.0 Volts, we suggest that you either

replace the item with an updated version or utilize a device to increase the voltage accordingly. There are

a number of readily available devices that may be used to increase the voltage such as ElectroDynamics’

%XIIHU$PSOL¿HU,QWHUIDFH'XUDOLWH¶V3RZHU%R[PDQXIDFWXUHGZLWKLQWKHODVWVL[PRQWKV(0FRWHF¶V'36,

products, Smart-Fly’s Power Expander and Powersystem, etc.

Link Procedure (TM-10 module/R6014FS receiver only):

Each transmitter has an individually assigned, unique ID code. In order to start operation, the receiver must be linked with

the ID code of the transmitter with which it is being paired. Once the link is made, the ID code is stored in the receiver

and no further linking is necessary unless the receiver is to be used with another transmitter. When you purchase another

R6014FS, this procedure is necessary; otherwise the receiver will not work.

1. Place the transmitter and the receiver close to each other within one (1) meter.

2. Turn on the transmitter.

3. Check the LED that is placed on the front side of the transmitter to see if the RF signal is active. When the blue LED is

ON solid, the RF signal is being sent.

4. Turn on the receiver.

5. Press down the Easy Link(ID SET) switch for more than one second, and release the switch. The receiver starts the

linking operation.

:KHQWKHOLQNLQJLVFRPSOHWHWKH/('LQWKHUHFHLYHUZLOOFKDQJHWRVROLGJUHHQ3OHDVHFRQ¿UPWKDWWKHVHUYRVZLOO

now operate by your transmitter. Please refer to the table below for the LED status of the receiver's condition.

No signal reception Red : On

Receiving signals Green: On

Receiving signals, but ID is unmatched. Green: Blink

Unrecoverable failure (EEPROM, etc.) Red and Green turn on alternately.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 118 119

Commentaires sur ces manuels

Pas de commentaire

Futaba 10C 2.4GHz Manuel d'utilisateur Page 20

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Futaba 10C 2.4GHz