Futaba 10C 2.4GHz Manuel d'utilisateur télécharger pdf (Page 15)

The initial charge, and any charge after a complete discharge, should

be at least 18 hours to ensure full charge. The batteries should be left

RQFKDUJH IRUDERXWKRXUVZKHQUHFKDUJLQJ WKHVWDQGDUG15-

NR4F1500 and NT8S700B Ni-Cd batteries.

We recommend charging the batteries with the charger supplied

with your system. Note that the use of a fast charger may damage the

batteries by overheating and dramatically reduce their lifetime.

You should fully discharge your system’s Ni-Cd batteries periodically to prevent a condition called memory.

)RUH[DPSOHLI\RXRQO\PDNHWZRÀLJKWVHDFKVHVVLRQRU\RXUHJXODUO\XVHRQO\DVPDOODPRXQWRIWKHEDWWHULHV

capacity, the memory effect can reduce the actual capacity even if the battery is fully charged. You can cycle your

batteries with a commercial cycling unit*, or by leaving the system on and exercising the servos by moving the

transmitter sticks until the transmitter shuts itself off. Cycling should be done every four to eight weeks, even

during the winter or periods of long storage. Keep track of the batteries capacity during cycling; if there is a

noticeable change, you may need to replace the batteries.

*Note that the 10C transmitter system has electronic protection from overcharging and reverse polarity via a poli-switch. It does NOT have a diode

LQWKHFKDUJHFLUFXLWDQGPD\EHGLVFKDUJHGSHDNFKDUJHGZLWKWKHEDWWHU\LQWKHWUDQVPLWWHU

DO NOT attempt to charge your 8-cell transmitter pack on the 4-cell receiver plug of the wall charger!

CHARGING THE Ni-Cd BATTERIES

Charging Your System’s Batteries

1. Connect the transmitter charging jack and airborne Ni-Cd batteries to the transmitter and receiver connectors of the

charger.

2. Plug the charger into a wall socket.

3. Check that the charger LED lights.

Receiver

Output and

Channel

Helicopter (

HELI

)

1 aileron (cyclic roll)

2 elevator (cyclic pitch)

3 throttle

4 rudder

5 VSDUHJ\UR

6 pitch (collective pitch)

7 VSDUHJRYHUQRU

8 VSDUHPL[WXUHFRQWURO

9 spare

10 spare

(Swash Type)

HR3H-1 H-3

ELE ELE

ELE1

ELE2

120˚

120˚120˚

PIT

(AIL)

AIL

(PIT)

PIT

(AIL)

AIL

(PIT)

HN3

120˚

ELE

PIT

AIL

HE3

ELE

PIT

(AIL)

AIL

(PIT)

PIT

(AIL)

AIL

(PIT)

H-2

PIT

FRONT

AIL

H-4

ELE1

ELE2 AIL

PIT

H4X

(Normal linkage type)

H-1:each servo linked

to the swashplate

independently.

Charger

TX: Transmitter charging indicato

RX: Receiver charging indicator

To transmitter charging jack

Receiver Ni-Cd battery

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 118 119

Commentaires sur ces manuels

Pas de commentaire

Futaba 10C 2.4GHz Manuel d'utilisateur Page 15

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Futaba 10C 2.4GHz