Futaba 10C 2.4GHz Manuel d'utilisateur télécharger pdf (Page 57)

Dual Elevator Servos (with a rudder) (

AILEVATOR

) (

ACRO

): Many models use two elevator servos, plugged in separate

receiver channels. (Flying wings without a separate aileron control use

ELEVON

. V-shaped tail models use

V-TAIL

, p. 58.

%HQH¿WV

• Ability to adjust each servo's center and end points for perfectly matched

travel.

• Ease of assembly, not requiring torque rods for a single servo to drive 2

surfaces.

(OHYDWRUVDFWLQJDOVRDVDLOHURQVIRU H[WUHPHVWXQWÀ\LQJRUPRUHUHDOLVWLFMHW

À\LQJRSWLRQDO

• Redundancy, for example in case of a servo failure or mid-air collision.

Adjustability:

• CH2 and CH8 only. (With programmable mixing, could utilize CH5 as the 2nd elevator servo. See www.futaba-rc.com\

faq\ for examples.)

THROTTLE-NEEDLE

uses CH8 and cannot be active simultaneously.

• Direction of each servo's travel may be reversed in

REVERSE

or the set percentages may be reversed here.

• Elevator travels independently adjustable (both directions and percent).

• Optional action as ailerons (defaults to

50%

UHVSRQVH7KLV UHVSRQVH FDQQRWEHDFWLYDWHGGHDFWLYDWHGLQÀLJKW6HWWLQJ

AIL1

and

GLVDEOHVWKLVIHDWXUH1RWHLI\RXZDQWWKLVEXWRQRIIZLWKDVZLWFKVHW

AIL1

and

here, and use 2

mixes .

AIL-to-ELEV

and

AIL-to-AUX2

OLQNWULPRIIDVVLJQDVZLWFKWRJHWDLOHURQDFWLRQIURPWKHHOHYDWRUVHUYRVZKHQWKH

assigned switch is on. See p. 68.

)RUGHWDLOVRQVHWWLQJXSDFRPSOH[DHUREDWLFSODQHVXFKDVRQHZLWKZLQJVHUYRVIXOOVSDQDLOHURQVÀDSV

AIRBRAKE

crow etc, please visit www.futaba-rc.com\faq\. Many other setups are also available.)

The

AILEVATOR

mixing function uses one servo on each of the two elevators, and combines the elevator function with the

aileron function (unless aileron travel is set to

). For aileron effect, the elevators are raised and lowered opposite of one

another in conjunction with the ailerons.

Once

AILEVATOR

LVDFWLYDWHGXQOHVV\RX]HURRXWWKHDLOHURQ¿JXUHVVHHEHORZDQ\WLPH\RXPRYH\RXUDLOHURQVRUDQ\

programming moves your ailerons (ie.

RUDDER-AILERON

mixing), the radio automatically commands both elevator servos

to also operate as ailerons. To deactivate this action, simply set the 2 aileron travel settings to

in the

AILEVATOR

function.

This way the elevators will work only as elevators.

,IXVLQJWKHHOHYDWRUVDVDLOHURQVDVZHOOEHVXUHWRPRYHWKHHOHYDWRUDLOHURQVWLFNZKLOHFKHFNLQJWKHVHUYRPRWLRQV,ID

ODUJHWUDYHOLVVSHFL¿HGZKHQWKHVWLFNVDUHPRYHGDWWKHVDPHWLPHFRQWUROVPD\ELQGRUUXQRXWRIWUDYHO

GOAL of EXAMPLE: STEPS: INPUTS:

Activate twin elevator servos.Deactivate

the elevator-acting-as-ailerons portion

of this function.

Note: Depending upon your model's

geometry, you may need to reverse one

servo or set a negative percentage here.

Open the

AILEVATOR

function.

for 1 second.

(If

BASIC

, again.)

AILEVATOR

Activate the function.

MIX

. to

ACT

Optional: adjust up/down travel when

operating as ailerons. (Ex:

AIL3

. to

AIL4

. to

Optional: adjust total elevator travel

of each servo. (Ex: right servo elevator

travel to

98%

, left to

96%

ELE2

. to

98%

ELE1

. to

96%

Close menu.

Where next? Adjust individual servo's

SUB-TRIMs

: see p. 49 and

END POINTs

: see p. 39.

Set up Twin Aileron Servos: see p. 51.

Set up

AIRBRAKE

mix: see p. 63.

1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 118 119

Commentaires sur ces manuels

Pas de commentaire

Futaba 10C 2.4GHz Manuel d'utilisateur Page 57

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Futaba 10C 2.4GHz