Futaba 10C 2.4GHz Manuel d'utilisateur télécharger pdf (Page 38)

Servo reversing (

REVERSE

): changes the direction an individual servo responds to a CONTROL STICK motion.

[Since channel 9 and 10 are switch only (and only available with a

PCM

2.4G-10CH

mode), its servo

REVERSE

is in the

AUX-CH

control screen with its switch assignment. See p. 46.]

For CCPM helicopters, be sure to read the section on

SWASH AFR

(p. 95) before reversing any servos.

Except with CCPM helicopters, always complete your servo reversing prior to

any other programming. If you use pre-built

ACRO



GLID

functions that control

multiple servos, such as

FLAPERON

V-TAIL

, it may be confusing to tell whether

the servo needs to be reversed or a setting in the function needs to be reversed.

See the instructions for each specialized function for further details.

Always check servo direction prior to every flight as an additional

SUHFDXWLRQWRFRQ¿UPSURSHUPRGHOPHPRU\KRRNXSVDQGUDGLRIXQFWLRQ

NOTE:

THR-REV

is a special function that reverses the entire throttle control, including moving the trim functionality to

the Stick’s upper half. To use

THR-REV

, turn off the transmitter, hold down the MODE and END keys, turn on. CURSOR

DOWN to

THR-REV

and turn the DIAL to

REV

. Turn the transmitter off and back on. This change affects all models in the

radio.

GOAL of EXAMPLE: STEPS: INPUTS:

Reverse the direction of the elevator

servo.

Open

REVERSE

function.

for 1 second.

(If

ADVANCE

, again.)

REVERSE

Choose proper channel and set

direction. (Ex:

ELE REV

)

ELE

REV

. for 1 second.

Close.

Where next? Adjust servo travel with

END POINT

: see p. 39.

6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO

D/R

EXP

): see p. 42.

6HWXSÀLJKWWLPHUVVHHS

Set up trainer functions: see p. 47.

Logic switch selection (

LOGIC SW

): The various functions in the T10C can be selected by switch. The Logic switch can be

assigned to the following functions:

THR-CUT

IDLE DOWN

AUX-CH

TIMER

PROG. MIX

AIRBRAKE

ELEV-FLAP

, and

AILE-FLAP

functions. The logic switch can activate functions by two switches combination. The 2 types of logic, either AND or OR,

can be selected.

Adjustability:

• Three logic switches can be used.

(Lsw1, Lsw2, and Lsw3)

• SW(1): Any

SWICH A-H or THR-

STKS, SW(2): Any SWICH A-H

• Switch position (

POSI

)

• Logic mode: AND or OR (

MODE

)

Logic combination table:

SWITCH LOGIC

SW(1) SW(2) AND OR

off off off off

off on off on

on off off on

on on on on

GOAL of EXAMPLE: STEPS: INPUTS:

Ex: Switch A and B are calculated by

AND logic. (A = down, B = down)

Open BASIC menu, then open

LOGIC

menu.

for 1 second.

(If

ADVANCE

, again.)

to 2nd page of menu.

LOGIC SW

Go to

POSI

and change setting.

(Ex:

DOWN

)

POSI

DOWN

Next,

POSI

DOWN

Repeat.

Close.

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 118 119

Commentaires sur ces manuels

Pas de commentaire

Futaba 10C 2.4GHz Manuel d'utilisateur Page 38

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Futaba 10C 2.4GHz