Futaba 10C 2.4GHz Manuel d'utilisateur télécharger pdf (Page 49)

SUB-TRIM

: makes small changes or corrections to the neutral position of each servo. Range is -120 to +120, with 0 setting,

the default, being no

SUB-TRIM

We recommend that you center the digital trims before making

SUB-TRIM

changes, and that you try to keep all of the

SUB-TRIM

values as small as

possible. Otherwise, when the

SUB-TRIMs

are large values, the servo's range

of travel is restricted on one side.

The recommended procedure is as follows:

• measure and record the desired surface position;

• zero out both the trims (

TRIM RESET

menu) and the

SUB-TRIMs

(this menu);

• mount servo arms and linkages so that the control surface’s neutral is as correct as possible; and

• use a small amount of

SUB-TRIM

WRPDNH¿QHFRUUHFWLRQV

GOAL of EXAMPLE: STEPS: INPUTS:

$GMXVWWKHÀDSVHUYRV

SUB-TRIM

untilits

center exactly matches the aileron

servo's center, as they are to work

WRJHWKHUDVÀDSHURQV

Open

BASIC

menu, then open

SUB-TRIM

for 1 second.

(If

ADVANCE

, again.)

SUB-TRIM

Choose the channel to adjust, andadjust

XQWLOVXUIDFHVPDWFK([ÀDS

FLAP

as needed.

to each channel,

Repeat for other channels.

as needed.

Close.

Where next? Adjust trim steps: see p. 48.

Adjust

END POINTs

: see p. 39.

6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO

D/R

EXP

): see p. 42.

The servo submenu includes two features:

• real-time bar-graph display to demonstrate exactly what commands the

transmitter is sending to the servos. (This can be particularly handy in setting

up models with complicated mixing functions, because the results of each

stick, lever, knob, switch input and delay circuit may be immediately seen.)

VHUYR F\FOH IXQFWLRQ WR KHOS ORFDWH VHUYR SUREOHPV SULRU WR LQÀLJKW IDLOXUHV

(channels 1-8)

GOAL of EXAMPLE: STEPS: INPUTS:

View the result of reassigning channel

6 from VR(A) knob to three-position

SWITCH C.

Cycle the channel 6 servo.

Complete desired programming

function. (Ex: in

AUX-CH

, move ch. 6 to

SWITCH C)

See

AUX-CH

for details. (p. 39.)

Open the

SERVO

function.

for 1 second.

(If

ADVANCE

, again.)

SERVO

Move each control to see exactly how

operating. (Ex: SWITCH C in all

positions)

C to center position.

Note change in position of ch. 6 servo.

Prepare all servos to be cycled and cycle.

Plug in servos. POWER ON.

End cycling and close.

Where next? 6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO

D/R

EXP

): see p. 42.

Set up desired programmable mixes: see p. 61.

Set up dual aileron servos: see p. 51.

Set up dual elevator servos: see p. 57.

SERVO

display and cycle submenu: displays radio's output to channels 1-10.

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 118 119

Commentaires sur ces manuels

Pas de commentaire

Futaba 10C 2.4GHz Manuel d'utilisateur Page 49

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Futaba 10C 2.4GHz