Futaba 10C 2.4GHz Manuel d'utilisateur télécharger pdf (Page 13)

NOTE: If you need to remove or replace the transmitter

battery, do not pull on its wires to remove it. Instead,

JHQWO\SXOORQ WKH FRQQHFWRUV SODVWLFKRXVLQJZKHUHLW

plugs into the transmitter.

Battery connector location

Charging jack

RF module

Trainer function

/DSC function

connector

Battery cover

NT8S

Ni-Cd battery

pack

Attachment of the Module

CAUTION

Be sure to turn off the power of the transmitter before

you install or replace the module.

To remove, press the tabs together and gently pull

rearwards. To install, line up the connector pins with

the socket in the rear of the module and gently snap

into position.

SWITCH ASSIGNMENT TABLE

• The factory default functions activated by the switches and knobs for a 10CA Mode 2 transmitter are shown below.

• Most 10C functions may be reassigned to non-default positions quickly and easily.

• Basic control assignments of channels 5-10 are quickly adjustable in

AUX-CH

(see p. 46). For example, the channel 5

servo, which defaults to SWITCH E for retract use, can easily be unassigned (NULL) to allow for easy use as a second

rudder servo in a mix, or to a slider or dial for bomb door or other control.

• Note that most functions need to be activated in the programming to operate.

• 10CA Mode 1, 10CH, and 10CP transmitter functions are similar but reverse certain switch commands. Always check

that you have the desired switch assignment for each function during set up.

Switch/Knob

A or H

Airplane (

ACRO

) Sailplane/Glider (

GLID

) Helicopter (

HELI

)

SWITCH A elevator dual rate

ch10

elevator dual rate

GRZQ EXWWHUÀ\RQ

ch10

elevator dual rate

ch10

SWITCH B rudder dual rate

ch9

rudder dual rate

ch9

rudder dual rate

ch9

SWITCH C up =

ELE-FLP

FHQWHUGRZQ 

IDLE-DOWN

down =

AIRBRAKE

up =

ELE-FLP

center = Distance cond.

down = Landing cond.

governor

SWITCH D aileron dual rate aileron dual rate aileron dual rate

SWITCH E or G* ODQGLQJJHDUFK WKURWWOHKROGFK

SWITCH F or H* VQDSUROOWUDLQHU trainer WUDLQHU

THR-CUT

SWITCH G or E* none up = Speed cond.

down = Start cond.

idle-up 1 and 2

SWITCH H or F* none LGOHXSJ\UR

KNOB A ÀDSFK

ÀDSWULPLI

FLAPERON

on)

ÀDS

ch6

HOVERING PITCH

KNOB B ch 8 ch 8 ch 8

KNOB C VSRLOHUFK

(disabled if

AIL-DIFF

on)

ch 7

(disabled if

AIL-DIF

on)

HOVERING THROTTLE

ch7

SLIDER D none ch 5 none

SLIDER E none none

HI-PIT

*On the 10CA Mode 2 transmitters, the TOP LEFT SWITCHES are spring-loaded and 2-position; on the 10CA Mode 1, 10CH, and 10CP, those

switches are on the right side. For consistency, the switch position’s designation remains the same (upper left is F, etc), but the functions are moved to

match the switch type.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 118 119

Commentaires sur ces manuels

Pas de commentaire

Futaba 10C 2.4GHz Manuel d'utilisateur Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Futaba 10C 2.4GHz