Futaba 10C 2.4GHz Manuel d'utilisateur télécharger pdf (Page 44)

44

GOAL of EXAMPLE: STEPS: INPUTS:

Set up aileron triple rates on SWITCH

C with travel settings of 75% (normal),

25% (slow roll) and 140% (extreme

aerobatics) and exponential settings of

0%, +15%, and -40% respectively.

NOTE: This normal rate has no

exponential so it has a very linear,

normal feel. This slow roll rate has

positive exponential (the opposite of

what most people normally use), which

makes the servos more responsive

around center. This makes the servos

feel the same around center in the

normal and low rates, but still gives a

very slow roll rate at full stick.

The 3D rate (extreme aerobatics) has

a very high distance of travel B nearly

twice that of the normal rate. Therefore,

using a very high negative exponential

setting softens how the servos respond

around center stick. This makes the

servos respond similarly around center

stick for a more comfortable feel.

Many modelers like to set up all 3 triple

rates on a single 3-position switch,

creating a “slow and pretty mode”,

a “normal mode”, and a “wild stunts

mode” all with the flip of a single

switch. To do so, simply set up rates

for all 3 controls and assign all 3 to the

same 3-position switch.

Open

D/R

,

EXP

function.

for 1 second.

(If

ADVANCE

, again.)

C

to

D/R

,

EXP

.

Choose the channel to change

(Ex: aileron is already selected)

C

to desired channel.

Optional: change switch assignment.

C

to

SW1

. to

C

.

Confirm switch is in desired position

and set rate. (Ex: up = high rate, 75%).

C

to

D/R>

.

C to up position.

AILERON STICK. to 75%.

AILERON STICK. to 75%.

Move SWITCH to 2nd rate position and

set this particular rate.

(Ex: center = low rate, 25%).

C to center position.

AILERON STICK. to 25%.

AILERON STICK. to 25%.

Optional: if using a 3 position SWITCH,

move SWITCH to 3rd position and set

this rate (Ex: down = 3D rate, 140%).

C to down position.

AILERON STICK. to 140%.

AILERON STICK. to 140%.

Optional: instead of using a switch,

you can set high rates to be triggered

when the stick moves past a certain

point. To test this, set aileron high rate

to 25%. Now set switch assignment to

AIL (90%). Move AILERON STICK

to the right and notice the huge jump in

travel after the stick moves 90% of its

distance.

C

to

SW1

. to

AILE (90%)

.

C

to

D/R>

.

AILERON STICK. to 25%.

AILERON STICK. to 25%.

AILERON STICK and watch

screen graph. See the change?!

You may also change the trigger point

by holding the stick at the desired point,

then pressing and holding the DIAL.

Set each rate’s

EXP

.

(Ex: 0%, +15%, -40%)

C

to

EXP>

.

C to up position.

&RQ¿UP

EXP

reads 0.

C to down position.

AILERON STICK. to +15%.

AILERON STICK. to + 15%.

C to center position.

repeat to set low rate expo to -40%.

Repeat above steps for elevator and rudder.

Close.

Where next? 6HWXSÀLJKWWLPHUVVHHS

Set up

TRAINER

functions: see p. 47.

Adjust the sensitivity of the trims: see p. 48.

Set up twin aileron servos: see p. 51.

Set up twin elevator servos: see p. 57.

6HWXSSURJUDPPDEOHPL[HVWRPHHW\RXUVSHFL¿FQHHGVVHHS

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 118 119

Commentaires sur ces manuels

Pas de commentaire