Futaba 10C 2.4GHz Manuel d'utilisateur télécharger pdf (Page 46)

Auxiliary channel function (including channel 9-10 controls)(

AUX-CH

GH¿QHVWKHUHODWLRQVKLSEHWZHHQWKHWUDQVPLWWHU

controls and the receiver output for channels 5-10. Also, the

CH9-10 POSI

are used to change the CH9-10 servo direction.

Note that the CH9-10 functions are only visible in the

AUX-CH

screen when

PCM

2.4H-10CH

modulation is selected. The

9-10th channels are not supported in

modulation. The 8-10th channels are not supported in

2.4G-7CH

modulation.

Adjustability:

• channels 5-8 may be assigned to any

SWITCH (A-H), LOGIC SWITCH

(Lsw1-Lsw3), slider [VR(D) and VR(E)], or knob [VR(A-C)] (for example,

moving flaps to a switch or slider), but not the primary control sticks (use

programmable mixes to do so, p. 68);

• channel 9-10 may be assigned to any

SWITCH (A-H), LOGIC SWITCH

(Lsw1-Lsw3) and the servo direction may be changed.

• multiple channels may be assigned to the same switch, slider or knob;

• channels set to "NULL" are only controlled by mixes. (Ex: utilizing 2 channels

for 2 rudder servos. See mixes, p. 68.)

•If

GYRO SENSE

, GOVERNOR, and

THR-NEEDLE

functions are activated,

AUX-CH

settings of related channels become invalid automatically.

Related channels:

GYRO SENSE

(

ACRO

): ch. 5, 7, or 8: see p. 73.

GYRO SENSE

(

HELI

): ch. 5: see p. 107.

GOVERNOR

(

HELI

): ch. 7, or ch. 7 and 8: see p. 108.

THR-NEEDLE

(

ACRO



HELI

): ch. 8: see p. 65.

Remember that if you assign primary control of a channel to a switch which you later use for other functions (like

GXDOWULSOHUDWHVRUDLUEUDNHVHYHU\WLPH\RXXVHWKDWRWKHUIXQFWLRQ\RXZLOODOVREHPRYLQJWKHDX[LOLDU\FKDQQHO

GOAL of EXAMPLE: STEPS: INPUTS:

$VVLJQÀDSVWRWKHULJKWVOLGHU>VR(E)]

and set channel 7 to

NULL

in preparation

to use it as a smoke system control (the

smoke system being activated later by a

throttle-to-ch.-7 mix).

Open

BASIC

menu, then open

AUX-CH

function.

for 1 second.

(If

ADVANCE

, again.)

to page 2.

AUX-CH

Choose the channel to change. (ex: ch.

6.)

Ch 7

Change primary control. (ex: to slider.)

Vr-E

Repeat as needed. (ex: ch. 7 to

NULL

Ch 7

. to

NULL

Close.

Where next? Programmable mixes: see p. 68.

6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO

D/R

EXP

): see p. 42.

Adjust

SUB-TRIM

of auxiliary channel to adjust center SWITCH position:

see p. 49.

Adjust

END POINTs

(sets end points of travel even when using a switch):

see p. 39.

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 118 119

Commentaires sur ces manuels

Pas de commentaire

Futaba 10C 2.4GHz Manuel d'utilisateur Page 46

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Futaba 10C 2.4GHz