Futaba 8FGAS, 8FGHS 2.4GHz Manuel d'utilisateur Page 113
- Page / 139
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
113
<Model Menu (Airplane/Glider Functions)>
● Select the function name
and return to the Model
menu by touching the
RTN button.
<SensorTouch™>
ELEVATOR ELEVATOR 2
(AILERON 5)
(AILERON 6)
AILEVATOR
[Corresponding model type]: Airplane/glider, Ailevator
(Effective only when 2 servos used at the elevators)
This function improves the performance of the roll
axis by operating the elevators as ailerons.
Ailevator is where each elevator in a standard
(conventional) or v-tail moves independently, like
ailerons on a wing. In addition to each elevator side
moving up and down together, each side moves in
opposite directions when moving as an Ailevator. On
a V-tail, this is also known as a Ruddervator, as they
can serve the same purpose. Typically, both Ailevator
and ailerons are coupled together to maximize roll
performance, especially on larger wingspan planes.
Note: Select Ailevator as the Model Type at the Model
Type screen. This changes the output channel. Check
the Function menu.
(Aileron function)
● When the elevators are used
as ailerons, aileron travel of
the left and right elevators
can be adjusted.
(Elevator function)
● The up and down rate of both
elevators when the elevator stick
is moved can be individually
adjusted.
● Select [AILEVATOR] at the Model menu
and access the setup screen shown
below by touching the RTN button.
Scrolling
● Moving cursor
● Selecting mode
● Adjusting value
● To next page
Setting method
● Travel adjustment
Move the cursor to the item you want to
adjust and touch the RTN button to switch to
the data input mode.
Adjust the rate by scrolling the touch sensor.
Initial value: ELE: +100%, AIL: 0%
Adjustment range: -120~+120%
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
Touch the RTN button to return to the cursor
mode.
*If the mixing direction is reversed, adjustments can be made
by changing the mixing rate polarity (+ or -).
*If a large value of travel is specified, when the sticks are
moved at the same time, the controls may bind or run out of
travel. Decrease the travel until no binding occurs.
- 8FG SUPER 1
- TABLE OF CONTENTS 2
- <Introduction> 4
- BEFORE USE 10
- Transmitter controls 13
- Receiver nomenclature 21
- Battery Charging 22
- Home screen 24
- User Menu 25
- <Basic Operation> 27
- Channel setting 27
- Easy Link (T8FGS/R6208SB) 28
- The present model 29
- Ailvator (Dual Elevator) 32
- Helicopter 34
- Fasten about 5-10cm 35
- Margin in the lead wire 35
- R6208SB Receiver 36
- MODEL BASIC SETTING PROCEDURE 37
- 12. Throttle mixing setting 42
- 13. Other special mixings 42
- System Menu functions table 43
- Mode and switch selection 45
- Operating mode selection 45
- USER NAME 48
- H/W SETTING 50
- Stick calibration method 51
- START SEL 52
- AUTO LOCK 55
- AUTO LOCK 55
- <SensorTouch™> 56
- FUNCTIONS OF LINKAGE MENU 57
- SERVO MONITOR 58
- MODEL SELECT 59
- Model deletion 60
- Model name change 60
- Model copy 60
- MODEL TYPE 61
- FREQUENCY 63
- FUNCTION 64
- SUB-TRIM 66
- FAIL SAFE 68
- END POINT 69
- IDLE DOWN 71
- SWASH RING 72
- PITCH ADJ 75
- T1-T4 SET 76
- Warning display: 77
- DATA RESET 78
- MODEL MENU (COMMON FUNCTIONS) 79
- CONDITION 80
- Condition delay setting 81
- DUAL RATE 82
- Dual rate setting procedure 83
- PROG. MIX 84
- FUEL MIX 86
- Model Menu functions list 88
- ( ) 89
- PIT CURVE 90
- THR CURVE 91
- THR DELAY 92
- AIL DIFF 93
- FLAP SET 94
- AIL to CMBFLP 95
- AIL to BRAKEFLP 96
- AIL to RUD 97
- RUD to AIL 98
- CAMBER MIX 100
- Setting method 101
- ●Activate the function 101
- ●Condition delay setting 101
- ●Rate adjustment 101
- ELE to CAMBER 102
- CMBFLP to ELE 103
- BUTTERFLY 104
- Fixed (0) Fixed (offset 105
- ●Reference point adjustment 105
- TRIM MIX 106
- AIRBRAKE 108
- ●Gyro type selection 111
- ●Sensitivity setting 111
- AILEVATOR 113
- ( ) 114
- RUD to ELE 117
- SNAP ROLL 118
- ●Master/single mode selection 119
- ●Direction switch selection 119
- MODEL MENU (HELICOPTER) 120
- PIT CURVE/PIT TRIM 121
- High Pitch/Low Pitch Trim 123
- THR CURVE/THROTTLE HOVER TRIM 124
- Throttle Hover trim 125
- Throttle limiter function 126
- THR HOLD 127
- SWASH MIX 128
- THROTTLE MIX 129
- GYRO mixing 131
- GOVERNOR mixing 133
- MODE 0％ 50％ 100％ 110％ 134
- TIMER ST1/ST2 135
- Switch Setting Method 137
- *[LOGIC] display blinks 139
- *The mode display blinks 139
Produits connexes et manuels pour Accessoires de communication Futaba 8FGAS, 8FGHS 2.4GHz
(93 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.176 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels