Futaba 8FGAS, 8FGHS 2.4GHz Manuel d'utilisateur Page 126
- Page / 139
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
126
<Functions of Model Menu (Helicopter Functions)>
Throttle limiter function
Setting method
*Set at the 3rd page of the throttle curve screen.
•Activate the function.
1. Select ACT and touch the RTN button.
2. Switch the display to ACT by scrolling the
touch sensor.
*The display blinks.
INH: Inhibit
ACT: Activate
3. Enter the selection by touching the RTN
button.
•ON/OFF switch setting
1. Select SW and touch the RTN button.
2. The H/W SET screen is displayed. Select the
hardware and touch the RTN button.
•High side operating range setting
1. Select HIGH and touch the RTN button.
2. Adjust the high side operating range by
scrolling the touch sensor.
*A gauge is displayed at the left side of the graph.
3. Touch the RTN button to switch to the cursor
mode.
•Low side operating range setting
1. Select LOW and touch the RTN button.
2. Adjust the low side operating range by
scrolling the touch sensor.
*A gauge is displayed at the left side of the graph.
3. Touch the RTN button to switch to the cursor
mode.
This function limits the high range of the throttle
movement by any slider or trimmer.
*Control which adjusts the limit point during ight can be set.
•Limiter operating range adjustment control
setting
1. Select CTRL and touch the RTN button.
2. The H/W SET screen is displayed. Select the
hardware and touch the RTN button.
*The throttle limiter operating position is indicated by a
dotted line on the graph.
*When limiter operating range adjustment control is NULL,
the throttle limiter function is not performed.
•Changing the control center position
1. Select CENTER and touch the RTN button for
1 second. CENTER changes from INH to “rate
display”.
2. When the CENTER rate is changed, the
neutral position of the hardware set at CTRL
can be adjusted.
*When CENTER is INH, the neutral position becomes the
LOW intermediate value.
*When CENTER is changed from INH to “rate display”, the
CENTER rate is set to the LOW intermediate value.
*The CENTER rate can be set between HIGH and LOW.
[Throttle limiter setting]
- 8FG SUPER 1
- TABLE OF CONTENTS 2
- <Introduction> 4
- BEFORE USE 10
- Transmitter controls 13
- Receiver nomenclature 21
- Battery Charging 22
- Home screen 24
- User Menu 25
- <Basic Operation> 27
- Channel setting 27
- Easy Link (T8FGS/R6208SB) 28
- The present model 29
- Ailvator (Dual Elevator) 32
- Helicopter 34
- Fasten about 5-10cm 35
- Margin in the lead wire 35
- R6208SB Receiver 36
- MODEL BASIC SETTING PROCEDURE 37
- 12. Throttle mixing setting 42
- 13. Other special mixings 42
- System Menu functions table 43
- Mode and switch selection 45
- Operating mode selection 45
- USER NAME 48
- H/W SETTING 50
- Stick calibration method 51
- START SEL 52
- AUTO LOCK 55
- AUTO LOCK 55
- <SensorTouch™> 56
- FUNCTIONS OF LINKAGE MENU 57
- SERVO MONITOR 58
- MODEL SELECT 59
- Model deletion 60
- Model name change 60
- Model copy 60
- MODEL TYPE 61
- FREQUENCY 63
- FUNCTION 64
- SUB-TRIM 66
- FAIL SAFE 68
- END POINT 69
- IDLE DOWN 71
- SWASH RING 72
- PITCH ADJ 75
- T1-T4 SET 76
- Warning display: 77
- DATA RESET 78
- MODEL MENU (COMMON FUNCTIONS) 79
- CONDITION 80
- Condition delay setting 81
- DUAL RATE 82
- Dual rate setting procedure 83
- PROG. MIX 84
- FUEL MIX 86
- Model Menu functions list 88
- ( ) 89
- PIT CURVE 90
- THR CURVE 91
- THR DELAY 92
- AIL DIFF 93
- FLAP SET 94
- AIL to CMBFLP 95
- AIL to BRAKEFLP 96
- AIL to RUD 97
- RUD to AIL 98
- CAMBER MIX 100
- Setting method 101
- ●Activate the function 101
- ●Condition delay setting 101
- ●Rate adjustment 101
- ELE to CAMBER 102
- CMBFLP to ELE 103
- BUTTERFLY 104
- Fixed (0) Fixed (offset 105
- ●Reference point adjustment 105
- TRIM MIX 106
- AIRBRAKE 108
- ●Gyro type selection 111
- ●Sensitivity setting 111
- AILEVATOR 113
- ( ) 114
- RUD to ELE 117
- SNAP ROLL 118
- ●Master/single mode selection 119
- ●Direction switch selection 119
- MODEL MENU (HELICOPTER) 120
- PIT CURVE/PIT TRIM 121
- High Pitch/Low Pitch Trim 123
- THR CURVE/THROTTLE HOVER TRIM 124
- Throttle Hover trim 125
- Throttle limiter function 126
- THR HOLD 127
- SWASH MIX 128
- THROTTLE MIX 129
- GYRO mixing 131
- GOVERNOR mixing 133
- MODE 0％ 50％ 100％ 110％ 134
- TIMER ST1/ST2 135
- Switch Setting Method 137
- *[LOGIC] display blinks 139
- *The mode display blinks 139
Produits connexes et manuels pour Accessoires de communication Futaba 8FGAS, 8FGHS 2.4GHz
(93 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.302 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels